Furnace Repair Services in Berwyn, PA

Homeowners who replaced an older furnace in the last several years often tell us the new one seems to run constantly. It usually is running, and in most cases that is the point. Modern staged and modulating equipment is built to run long and low rather than short and hot, and it takes some getting used to after decades of a furnace that roared on and shut off.

Davis Modern Heating & Cooling repairs heating equipment throughout Berwyn and the surrounding Easttown and Tredyffrin areas. We have been family owned since 1850, we service every brand, and we work across natural gas, propane, heating oil, and electric.

Our Services

*Required Fields

First Name

Last Name

Phone Number

Email Address

Message

By submitting this form and signing up for texts, you consent to receive text messages from Davis Modern Heating & Cooling at the number provided, including messages sent by the auto dialer. Consent is not a condition of purchase. Msg & data rates may apply. Msg frequency varies. Unsubscribe at any time by replying STOP to 610-277-2656 or clicking the unsubscribe link (where available), and no further messages will be sent. Reply HELP for help. See Privacy Policy & Terms.

Why Homeowners in Berwyn, PA Trust Us

We have had a great experience with them for both AC service and our boiler. The service team is professional, knowledgeable, and kind. They also make a big effort to get your job taken care of as soon as possible.

Tom, Julian, and Collin did a fantastic job replacing my oil furnace with a natural gas one. This was a very involved oil to gas conversion and they did a fantastic job running the gas lines and installing the new water heater. They were very courteous and did a great job explaining everything. Fair pricing, I would highly recommend!

I've had to call Davis on several occasions with furnace issues. Each time it was fast responses pleasant & friendly technicians they were very informative & got my heater up & running fast. 5 stars from me.

Extremely happy with our experience. We scheduled a tune up thereafter and the technician Nick H professionally maintained our systems, gave us valuable recommendations, and personally rerouted some HVAC piping to help provide additional head clearance in our tight mechanical room without asking. Highly recommend all around.

Furnace was clicking but not igniting. Called Davis and they said they were backed up but would try to get to me. Half hour later they called and said a technician was on their way. Nick arrived and quickly diagnosed the problem. Am up and warming up! Great service! Would highly recommend

When Normal Operation Is Not Normal

Knowing what is normal makes it easier to spot what is not. These are real problems.

No heat at all
Cycling every few minutes
Error code displayed
Blower running without heat
Repeated lockouts
Loud ignition or startup
Rooms significantly uneven
Fuel use jumping suddenly
Burning or electrical smell
Any alarm sounding

Long, steady low fire operation does not belong on that list, even though it surprises people.

Why a Modern Furnace Runs Differently

A single stage furnace has one output and one answer to every condition, which is why it blasts heat and then shuts off. Two stage and modulating equipment instead matches output to demand, running at a fraction of capacity for long stretches on mild days. That produces steadier temperatures, less noise, and better efficiency, and it looks nothing like what a homeowner is used to.

The problem comes when the control does not match the equipment. A single stage thermostat wired to a two stage furnace locks it into one mode, and a control configured with the wrong cycle rate or minimum runtime will drive the furnace in ways the manufacturer never intended. The equipment is capable and the settings are preventing it from doing what it does well.

Ductwork is the other limit. Homes here frequently had new high efficiency furnaces installed on duct systems laid out in the 1950s, and a variable speed blower fighting high static pressure will not deliver what the equipment is rated for. Measuring static pressure tells us in minutes whether the problem is the furnace or the path it is pushing air through.

What We Check on a Heating Call

A heating call starts with what the system is doing and what it is being told to do. We confirm the thermostat type, staging configuration, and wiring, then test ignition and flame sensing, gas or oil pressure, blower operation, static pressure, safety controls, venting, and temperature rise, and we inspect the heat exchanger on every visit.

We repair and install furnaces, boilers, oil furnaces, heat pumps, thermostats, zone controls, ductwork, and ventilation on every brand and fuel. Communicating and multi stage systems are ordinary work for us rather than something we hand off.

Where equipment is at the end of its life, we explain the reasoning and lay out options across all fuel types, sizing to the house and its ducts rather than to the furnace that came out. We also have more than thirty five years of experience with geothermal heat pumps and solar heating.

What We Found in Berwyn

Steve called from Berwyn in December convinced his two year old furnace was failing, because it ran for long stretches and never seemed to shut off the way his old one had.

Our technician confirmed the furnace was operating correctly on low fire, then found the thermostat configured as single stage and cycle settings that were forcing it to overshoot and coast. We corrected the configuration, verified staging under load, measured static pressure and temperature rise, and cleaned the flame sensor while on site.

Temperatures evened out across the house and fuel use dropped compared with the previous month. Nothing had been broken, it had simply never been set up to operate the way it was designed to.

What Berwyn Households Can Expect

Here is what our team brings when we take a call.

The same family since 1850
Staged and modulating equipment
Controls and configuration expertise
Technicians on call 24/7
Pennsylvania licensed
Static pressure measurement
Plain explanations of findings
Homes and commercial properties

Our on-call service covers nights, weekends, and holidays, so a furnace that actually does fail after hours gets a technician rather than a wait.

Frequently Asked Questions

Is it normal for a new furnace to run for long periods?

Yes, for two stage and modulating equipment. Long low fire cycles are how those systems deliver steady temperatures and better efficiency.

Does my thermostat need to match my furnace staging?

It does. A single stage control on a multi stage furnace prevents the equipment from using its lower output, which affects both comfort and efficiency.

Do you offer after hours heating service?

Yes. We keep technicians on call 24 hours a day, seven days a week.

What does an error code on my furnace mean?

Codes indicate which component or safety the control is reporting on. They narrow the diagnosis considerably, so it helps to note the pattern before calling.

Can old ductwork limit a new furnace?

Yes. High static pressure from undersized or restricted ducts keeps a modern furnace from delivering rated performance, and it shortens blower life.